192.168.33.1 – Default Login, Password & Reset Guide

192.168.33.1 is the default admin address used by Huawei and Shelly devices to open their login page. If your router, extender, or smart device connects through one of these brands, typing this address into your browser takes you straight to the settings panel.

In this guide, I’ll walk you through logging in, finding the default password, fixing common errors, and resetting your device, based on the same steps I use whenever a client hands me one of these devices.

192.168.33.1 Admin Login

Admin

Login

192.168.33.1 IP Address

192.168.33.1 is a private IP address, more exactly a private IPv4 address, taken from the reserved block that RFC 1918 sets aside for private networks. It sits inside the wider 192.168.0.0/16 range, a Class C-style private range that never touches the public internet. Most home routers use 192.168.0.1 or 192.168.1.254, but a few brands picked this address instead.

Huawei WS322, Huawei WS323, and Huawei PT530 are the main networking devices that use it as their default gateway, since Huawei treats it as one of several default gateways depending on firmware, and the same goes for other Wireless Range Extender models. Shelly, the smart home devices brand, uses it too, for the Shelly 1, Shelly Plug, and Shelly EM. As a shared Powerline Access Point address, it works almost like a universal access point for smart IoT devices, each opening its own Wi-Fi hotspot with a web interface at this gateway.

A few basics worth knowing before you open a wifi router or Shelly device at this address:

It’s a local ip address, not a router admin ip address reachable from outside your home network.
You reach it by typing it into your web browser’s address bar.
The page that opens is either an admin panel or a plain admin page.
Some devices show a Login Admin button; others load a login form right away.
Always click the correct link and stay on the same network as the device.

Default Login, Username and Password for 192.168.33.1

On first login, most of these devices don’t ask much. All Gen 1 devices from Shelly the Shelly 1, Shelly Plug, and Shelly EM ship with no Username or Password at all. The field is left blank, since authentication only turns on once you set it up yourself.

Huawei’s side works differently. The WS322 Wireless Range Extender and WS323 Wireless Range Extender use admin as both Username and Password, and the PT530 Powerline Access Point follows the same factory default pattern. Since 192.168.33.1 is the shared gateway address across this whole group of devices, it helps to know exactly which Brand and Model you have.

Here’s the Most popular Default Logins table for quick reference:

Brand	Model	Username	Password
Huawei	WS322 / WS323	admin	admin
Huawei	PT530	admin	admin
Shelly	Shelly 1 / Plug / EM / Vintage	none	none

A few extra points to keep in mind:

The “1234” code some guides mention isn’t tied to 192.168.33.1 devices; it belongs to a different IP Address range entirely.
If none of the original login details work, a factory reset restores everything to factory default and gets you back to the default IP address.
The reset instructions are the same across devices: hold the reset button, wait, and the device reboots with its default credentials active again.
This works close to 100% of the time, and it’s the fastest way to protect your network on a used router or extender.

How to Login and Access 192.168.33.1

Getting in takes a few simple steps on a computer or phone. First, make sure you’re on the correct network. This means joining the Wi-Fi network (or wireless network) that the device broadcasts, or plugging in with an Ethernet cable for a more stable wired connection.

Login Using Wi-Fi

For Shelly devices, connect to the network named shelly-[model]-[ID], visible under your Wi-Fi settings, before you’ve even set the router’s name.
Open any web browser Chrome, Firefox, Safari, or Edge and type http://192.168.33.1 straight into the address bar.
Don’t search it in a search engine, since search results sometimes point to the wrong models’ configuration page.
A login page (or login prompt) should appear right away.

Login Using Ethernet Cable

Connect router cable directly with an Ethernet cable for the most reliable wired connection.
Open your web browser and type the same address, http://192.168.33.1, into the address bar.
This method skips Wi-Fi issues completely, so it’s the best option if the page keeps failing to load over Wi-Fi.

For Huawei devices such as the WS322, WS323, and Huawei PT530, the default login username and password is almost always admin and admin unless someone already changed it. Check the back of router packaging if you’re unsure, since the default values and default username are often printed there, along with the default credentials.

For a Shelly smart device, there’s usually no root, admin, or default password required at all. The field is left blank and you log straight into the Shelly web interface. Once in, the admin panel and wider web interface show connected device statistics, let you review network and router settings, and give you access to a Save button whenever you change something.

Pro Tip: If the address fails to load, check the Default Gateway your computer sees, since device behavior after a firmware update can quietly switch you to a different Shelly device’s own Wi-Fi access point. If you’ve been logged off, your login credentials should still be the same username and password combo you set earlier for that user. Keep a copy in your router manual notes rather than relying on memory the risk of forgetting them is real, and the SSID and password sticker on the device often carries the IP address too.

Troubleshooting: If You Can’t Access 192.168.33.1

When the Router login page is simply not loading, work through it step by step instead of guessing.

Quick Checks First

Verify your connection make sure you’re actually connected to wi-fi on the right Wi-Fi network, or plugged into the home router’s network directly.
Make sure you’re not still connected to a Shelly hotspot left over from an earlier setup.
Disable VPN or proxy software before you try again, since VPN connections and leftover browser proxy settings are common reasons a Router login page won’t load.

Find Your Router’s IP Address

If the address still looks wrong, run a few checks to find router’s IP address for certain:

Windows: Open Command Prompt (cmd) and run ipconfig /all. Look at the Default Gateway field to Check your actual gateway rather than assuming it’s still 192.168.33.1.
macOS or Linux: Open Terminal and run netstat -nr, or use grep default to get the same information.

These checks matter because a wrong router IP address, or a different IP address caused by an IP address conflict between two devices on the same private addresses range, is exactly what causes problems with speed and dropped connections not just a login failure.

Browser-Related Fixes

If http://192.168.33.1 isn’t loading:

Try a different browser, or switch your usual browser into incognito mode or a private/incognito window.
Clear cached DNS entries and disable Browser extensions that might interfere.
Turn off HTTPS-only settings baked into some browsers, since they can silently block a plain HTTP login page and cause issues loading otherwise correct pages.
Type the right address again carefully this fixes it more often than people expect.

Forgot Login Password

You may be dealing with a wrong username and password rather than a wrong address. Forgot Login Password situations are common on used gear where someone changed the credentials and never wrote them down.

At that point, hard resetting the device is usually the fastest path:

Look for a small black button on the back of router (some guides call it the reset pin).
Hold it for about 10 seconds.
The unit reboots to factory settings a default one, with whatever IP address router list entry it shipped with restored.

This works the same for Shelly devices as it does for a Huawei extender or Powerline unit, and it’s covered in most manufacturer reset instructions and any decent tutorial or guide online, including this full walkthrough.

One more thing: Check for IP conflicts before assuming the router itself is broken. If your computer was manually assigned a static address that overlaps with DHCP assignments elsewhere on the network, you’ll get flaky access to the router’s admin panel even though nothing about the device changed. A different router on the same network can also hand out competing addresses, so disconnect other hardware and try to login again on a clean network.

Brands Using 192.168.33.1

Only a small group of brands ship hardware pointed at this universal web interface address:

Huawei models WS322 Wireless Range Extender, WS323 Wireless Range Extender, and PT530 Powerline Access Point, all sharing 192.168.33.1 as a default gateway.
Shelly its Generation 1 line of smart home devices reuses the exact same address for its local setup screen.

Beyond Huawei and Shelly, no other major brands lean on this address by default.

How to Reset Devices Using 192.168.33.1

Resetting isn’t identical across every device, but the underlying procedure rhymes.

Reset Steps for Huawei Devices

Locate the dedicated reset button or small recessed button on the back or bottom of the device (sometimes on the rear panel instead) this applies to any Huawei networking device or extender, including the PT530.
Grab a paperclip or toothpick and hold the pin down.
Wait a factory reset triggered this way typically takes about 10 seconds to a full 60 seconds, depending on the model.
Watch the indicator lights or LED: it will flash three times, or blinks rapidly, right before the device manages to reboot fully.
Once the LED indicator goes solid again, the factory reset erases whatever custom settings, schedules, and Wi-Fi credentials you’d built up.
You’re back to no username or password required, or on Huawei gear, back to username admin and password admin, restored to factory defaults.

If you’d rather skip the button entirely on some Huawei units, simply unplug the power cord and plug back in while holding the reset pin same result, cleaner grip.

Reset Steps for Shelly Devices

Shelly Gen 1 devices and any other Shelly smart device use a different change pattern. There’s no small button hunt here rapid power cycles do the job instead:

Power on and off the plug five times in quick succession, roughly 1 second on and 1 second off each time, right after it’s powered on from a cold start.
By the fifth cycle, the unit gives up on connecting to your regular network and opens its own Wi-Fi hotspot again, broadcasting as shelly-[model]-[ID], exactly like it did on day one.

Before doing any of this to regain access after a forgotten admin password, note down settings you actually care about there’s no walking it back once the flash happens. Once reset, connect phone or computer to the fresh hotspot, navigate to http://192.168.33.1, and log in with the blank password (or default) to start over.

Changing Your Password on Devices at 192.168.33.1

Changing the admin password is one of the first things worth doing, and honestly one of the most skipped steps.

For Huawei Devices

Log in and open the admin panel on your Huawei WS322/WS323/PT530 unit.
Find Security or System under the main menu the exact label shifts a little across firmware versions, but it’s usually filed under Settings or an Administration section.
Look for Change Password (sometimes buried in Account Management).
Enter your current password, type a new password, and confirm it.
Hit Save or Apply.

A strong password should mix uppercase letters, lowercase letters, numbers, and symbols, run at least 12 characters, and avoid anything tied to the device’s serial number or device type. Reusing factory default credentials or leaving default credentials in place at all is a real security risk once the device is reachable from beyond your own four walls.

For Shelly Devices

Connect to the device while it’s on the same network, or its own Shelly hotspot if you’re setting it up fresh.
Log into Login, and toggle the Restrict Login toggle on if it isn’t already this is exactly how you change admin password behavior going forward, forcing a username and admin password to be required.
Update your Wi-Fi password separately if the hotspot itself needs a credentials update.

Whatever you alter settings-wise, expect to log in again afterward the session usually drops the moment you confirm a change, which is normal and not a sign that anything broke.

Router Username and Password List

Not every device on this address is Huawei or Shelly gear. Some general router lists just happen to include 192.168.33.1 as a secondary entry. One older listing worth mentioning:

Brand	Model	Wireless	Protocol	Username	Password
2Wire	HOMEPORTAL Rev. SBC YAHOO! DSL	ALL WIFI ROUTERS	HTTP	none	none

Note the capitalization varies by source you’ll see it written as 2WIRE or 2Wire depending on the guide, but it’s the same Brand either way, with the Username and Password fields both left blank by default.

What Is 192.168.33.1 and Why Does It Matter?

Zoom out, and 192.168.33.1 is just one gateway pulled from a much bigger family. IANA the Internet Assigned Numbers Authority set aside the whole 192.168.0.0–192.168.255.255 range for private networks under RFC 1918. Inside that, the 192.168.x.x family gets carved into individual subnet blocks.

This particular one, the 192.168.33.0/24 subnet, runs from network address 192.168.33.0 up through broadcast address 192.168.33.255, sometimes reserving 192.168.33.254 near the top for a secondary gateway. It has 254 host addresses in between, available for local devices.

Quick subnet reference:

Detail	Value
Subnet	192.168.33.0/24 subnet
Network address	192.168.33.0
Broadcast address	192.168.33.255
Usable host addresses	254 host addresses
Gateway	192.168.33.1

Your laptop might land on 192.168.33.2, a tablet on 192.168.33.3, a smartphone on 192.168.33.4, and so on usually automatically assigned by whatever DHCP server the router or Huawei PT530 is running. Compare that against neighboring blocks like 192.168.0.1, 192.168.2.1, 192.168.8.1, 192.168.10.1, or 192.168.100.1 all valid private gateway addresses too, just from different subnet slices of the same broader range.

On a home LAN or small local area network, this gateway is the actual gateway your traffic passes through before it ever reaches the internet. It routes traffic out toward your ISP’s connection and back, acting as the single destination address every local device checks in with first. None of it is reachable from the public internet directly, which is the whole point of using static IPs or DHCP-issued addresses from a Class C private IPv4 address block.

This matters practically if you’re trying to troubleshoot connectivity issues, set up port forwarding rules for something like a Shelly smart relay, or figure out why one gadget can’t see another. Knowing which subnet and gateway you’re actually on is the real source of most confusion not the device itself.

Frequently Asked Questions

What is 192.168.33?

192.168.33 refers to the first three sets in a standard IPv4 address made of 4 sets of numbers separated by dots in this case 192, 168, and 33. Add a fourth set, anywhere between 0 and 255, and you get a unique address like 192.168.33.1 for a specific device. The first three sets act as the network id (192.168.33), while the last set works as the device id .1 is simply the most common choice for the default IP address, distinct from anything reachable on the internet, and shorthand 168.33.1 is sometimes used loosely to mean the same thing.

How do I login to 192.168.33?

Type 192.168.33.1 into your browser’s address bar, press enter, and you’ll land on a Login screen asking for a username and password. Fill both in and hit OK to get through.

What are the most common default logins for 192.168.33?

The most common default logins at this IP address are simply admin for both Username and Password that’s the pattern across nearly every device sitting on 192.168.33.1.

What is the most common default username for 192.168.33?

The default username for this address is, almost without exception, admin true for essentially every device on 192.168.33.1.

What is the most common default password for 192.168.33?

Same story for the default password at this address: admin, again matching what you’ll find on 192.168.33.1 across the board.

How do I access the router IP address at 192.168.33?

To access the router, type 192.168.33.1 into your browser’s address bar, wait for the LOGIN prompt, enter admin as both username and password (the default logins for most of these devices), and press OK.

How do I go to 192.168.33 or use 192.168.33?

Getting access works the same way every time: browser’s address bar, 192.168.33.1, LOGIN, admin as username and password, OK. That’s the whole routine, and it’s worth memorizing since the default logins rarely change from device to device.

Which router brands use 192.168.33.1 as their default IP?

Two brands, really: Huawei models like the WS322 Wireless Range Extender, WS323 Wireless Range Extender, and PT530 Powerline Access Point, plus Shelly’s Generation 1 line of smart home devices. Both treat this as their universal web interface address and default gateway, and no other major brands lean on it the same way.

Why can’t I open 192.168.33.1 in my browser?

Usually because you’re on the wrong network. For Shelly devices, you may need to join the Shelly device’s own Wi-Fi hotspot first rather than your home Wi-Fi, while Huawei devices generally expect a direct Ethernet or local network connection. Typing the address into a search engine instead of the address bar is another common mistake, and forcing https:// instead of plain http://192.168.33.1 will also break the page on most of this hardware.

What is the default username and password for 192.168.33.1?

On Huawei WS322, WS323, and Huawei PT530, the default username and password pair is admin and admin, with authentication enforced by default on the web interface. Shelly devices skip this entirely no login restriction is active out of the box, so you get in with a blank password until you set your own login credentials.

Is 192.168.33.1 safe to use?

It’s safe in the sense that 192.168.33.1 is a private IP address only reachable on your local network, never exposed directly to the public internet. The real risk isn’t the address itself but leaving a default admin password in place on a Shelly device or Huawei unit, which opens the door to unauthorized access from anyone who later joins that same network.

Can two devices on my network share the IP 192.168.33.1?

Not without problems. Two devices claiming 192.168.33.1 on the same 192.168.33.0/24 subnet creates a straightforward IP address conflict, and connectivity for one or both will drop. Run a network scanner or check your router’s DHCP client list to see which assigned addresses are actually in use before manually setting an IP address on any device.

How do I find out if 192.168.33.1 is my default gateway?

On Windows, open Command Prompt and run ipconfig /all, then read the Default Gateway value it’ll show 192.168.33.1 if that’s really your gateway, or something else entirely like 192.168.1.254 or 10.0.0.1 if it isn’t. On macOS or Linux, open Terminal and run netstat -nr or grep default instead. Either way, that number is what you type into your router’s admin panel.

What subnet does 192.168.33.1 belong to?

It sits in the 192.168.33.0/24 subnet a Class C-sized private subnet running from network address 192.168.33.0 up to broadcast address 192.168.33.255, with 254 host addresses available in between (192.168.33.254 among them). You’ll see this exact range used both at home and in small office environments, with 192.168.33.1 simply claimed as the gateway.